VMX-H Series Configured Soft Starter

Configured Soft Starter in NEMA 4/12 Enclosure

AC Supply Voltage: 200 to 600 Vac

HP Ratings: 5 to 1000 HP

Amp Ratings: 21 to 960 Amps

Overload Rating: 500% for 60 sec (1.15 SF)

Enclosure: NEMA 4/12

Bypass: Line Start Rated Contactor


Power Components
6 SCRs in inverse parallel pairs for full phase angle
soft start control
1600V PIV rating on all units
RC snubber for dv/dt protection of each SCR pair
Dry contact closure selects a non-ramping Jog
function at an adjustable torque
Line Voltage Range
200 to 600 VAC, 3 phase +10% -15% on all units,
Kick Start
10 - 100% starting torque for 0.1 - 2 seconds
Current Ratings
18 - 1250A depending on unit selection
Range of each unit is 50-100% of maximum
Pump-Flex™ Deceleration Ramp
Fully adjustable to match field conditions:
Begin Decel setting, 0 - 100% of line voltage
Decel ramp time, 1 - 60 seconds
End Decel setting (Off ), 0 - 1% of Begin setting
AC Supply Voltage
User supplied 120VAC +10% -15% tolerance, 60Hz
Optional 240VAC 50Hz control available
Restart Delay Timer (Sequential Start Delay)
Programmable time delay 1 - 999 seconds after loss
of control power for staggered restarts
Overload Capacity (% of motor FLA)
500% for 60 seconds, 1.15 SF
RS-485 Serial Communications
Up to 247 starters per link
Modbus RTU protocol built-in
Full programming over the serial link
Programmable remote starter control
Bypass Contactor
Standard on all units
Standard Duty: Shunt rated bypass
Heavy Duty (Across-the-Line) line start rated bypass
Operator Interface
Tactile feedback keypad
Easy to read LED display
Run and fault
status indicators
Start/Stop Control Choices
2-wire Run-Stop using dry contacts
3-wire Start/Stop with built-in seal in contact
N.C. Interlock input (dry contact) for remote devices
Electronic Shear Pin Protection
Trip level: 100 - 300% of motor FLA with trip delay
Ramp Control Choices (4 built-in)
Voltage Ramp
Voltage Ramp with Current Limit
CLT© Closed Loop Torque Ramp (Current Ramp)
Current Step (current limit only)
Ramp times adjustable 1 - 120 seconds
Current Limit adjustable 200 - 600% of FLA
Motor Duty Cycle Protection
Back-spin/coast-down, starts-per-hour or minimum
time between starts lockouts. Restart delay after a
power failure.
Dual Ramps
Select via dry contact closure between any
combinations of the above
Short Circuit
Trips at 10x unit current rating during run. Checks for
shorted load prior to each start.
Start & Run Protection
Two programmable overload trip curves allow for the
thermal capacity required to start the load while providing
motor overload protection needed during the run time.
Start: Programmable for Class 5 - 30
Run: Programmable for Class 5 - 30, enabled when starter
detects motor is "At-Speed"
Reset: Manual or automatic, selectable via programming.
Remote reset available.
Shorted SCR
Locks out on any single shorted SCR (defeatable) or
can provide shunt trip function if multiple SCRs short
or bypass contactor is welded closed.
Real-Time Thermal Modeling
Continuously calculates motor operating temperature even
when the motor is not running.
Monitors phase current, ground current and motor
thermal capacity.
Retentive Thermal Memory
Remembers the thermal condition of the motor even in the
event of a power brown-out or black-out when power is
restored. Extrapolates motor temperature using a real-time
Phase Loss
Trips on phase current or voltage loss
Dynamic Reset Capacity
Overload will not reset until thermal capacity in the motor is
sufficient for a successful restart. Starter learns and retains this
information from previous starts.
Phase Rotation
Phase rotation trip can be set to A-B-C, A-C-B or disabled.
Motor Temperature
PTC thermistor input can also be used for E-stop or external
overload relay.
Equipment Ground Fault
Residual current method with adjustable trip delay.
Phase Current Imbalance/Loss Protection
Trip level: 5 - 30% current imbalance between any two
phases with trip delay